Elo Touch Solution E812229 Podręcznik Użytkownika

Elo Entuitive TouchmonitorUser GuideFor 15” LCD DesktopET1529L SeriesRevision.B

Customer DisplayThe Customer Display is a twenty character two line vacuum fluorescent display (VFD).It consists of a VFD and VFD controller.Serial Ve

vTABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS ... 1 FEATUR

viFigure 1-1. 3-Track USB Keyboard Emulation IntelliHead

1SECTION 1. FEATURES AND SPECIFICATIONS The USB (Universal Serial Bus), HID Keyboard Emulation, Swipe Reader is a compact magnetic stripe card reade

USB HID Keyboard Emulation Swipe Reader 2The hardware configurations are shown in Table 1-1. Table 1-1. Configurations ACCESSORIES The accessories

Section 1. Features and Specifications3SPECIFICATIONS Table 1-2 lists the specifications for the USB IntelliHead. Figure 1-2 shows the dimensions f

USB HID Keyboard Emulation Swipe Reader 4

5SECTION 2. INSTALLATION This section describes the cable connection, the Windows Plug and Play Setup, and the physical mounting of the unit. USB C

USB HID Keyboard Emulation Swipe Reader 6

7SECTION 3. OPERATION CARD READ A card may be swiped past the read head at any time. The magnetic stripe must face toward the head and may be swip

USB HID Keyboard Emulation Swipe Reader 8

SpecificationsSensor SecuGen FORImage Capture Speed 600ms/frameImage Transfer Speed 500Byte/msPixel Resolution 356x292USB Signaling Type Full Speed Ty

9SECTION 4. USB COMMUNICATIONS This device conforms to the USB specification revision 1.1. This device also conforms with the Human Interface Device

USB HID Keyboard Emulation Swipe Reader 10MSR (Non-Keyboard Emulation Version). Please refer to Technical Manual 99875320 for further information reg

Section 4. USB Communications11PROGRAMMABLE CONFIGURATION OPTIONS This device has a number of programmable configuration properties. These properti

USB HID Keyboard Emulation Swipe Reader 12REPORT DESCRIPTOR The HID report descriptor is structured as follows: Item Value(Hex)Usage Page (Generic De

Section 4. USB Communications13COMMANDS Command requests and responses are sent to and received from the device using feature reports. Command requ

USB HID Keyboard Emulation Swipe Reader 14RESULT CODE This one-byte field contains the value of the result code. There are two types of result codes

Section 4. USB Communications15Property ID is a one-byte field that contains a value that identifies the property. The following table lists all the

USB HID Keyboard Emulation Swipe Reader 16SERIAL_NUM PROPERTY Property ID: 1 Property Type: String Length: 0 – 15 bytes Get Property: Yes Set Pro

Section 4. USB Communications17bus bandwidth used by the device, and slowing down the card data transfer rate decreases the USB bus bandwidth used by

USB HID Keyboard Emulation Swipe Reader 18TRACK_DATA_SEND_FLAGS PROPERTY Property ID: 4 Property Type: Byte Length: 1 byte Get Property: Yes Set P

Six Port USB HubThe Hub provides 4 internal USB ports to be used by the credit card reader, the finger-print reader, the touchscreen, and the customer

Section 4. USB Communications19TERMINATION_CHAR PROPERTY Property ID: 5 Property Type: Byte Length: 1 byte Get Property: Yes Set Property: Yes D

USB HID Keyboard Emulation Swipe Reader 20SS_TK3_ISO_ABA PROPERTY Property ID: 8 Property Type: Byte Length: 1 byte Get Property: Yes Set Property

Section 4. USB Communications21This property is stored in non-volatile EEPROM memory so it will not change when the unit is power cycled. When this

USB HID Keyboard Emulation Swipe Reader 22PRE_TK_CHAR PROPERTY Property ID: 13 (0D hex) Property Type: Byte Length: 1 byte Get Property: Yes Set P

Section 4. USB Communications23according to a United States keyboard keymap. For example, to transmit the ASCII character ‘?’ (063 decimal), the cha

USB HID Keyboard Emulation Swipe Reader 24Description: The value is a byte that represents the devices interface type. The value can be set to 0 for

25SECTION 5. DEMO PROGRAM The purpose of this demo program is not to demonstrate card reading with this HID keyboard emulation device. Use a text ed

USB HID Keyboard Emulation Swipe Reader 26• Enter a command in the Message edit box. All data entered should be in hexadecimal bytes with a space bet

27APPENDIX A. USB INTELLIHEAD SWIPE READER The following drawing is provided in this section: Part Number Title 21030007 USB-KB INTHD 3TK 125MM W

USB HID Keyboard Emulation Swipe Reader28Figure A-1. USB Keyboard Emulation, For Swipe Readers, 125mm Wire, 5-Pin Connector

C H A P T E R2INSTALLATION AND SETUPThis chapter discusses how to install your LCD touchmonitor and how to install EloTouchSystems driver softwa

INSTALLATION GUIDE LD9000U series User Manual available at our web site www.logiccontrols.com USB Interface Customer Pole Displays LD9000U, LD920

Logic Controls, Inc. SOFTWARE COMMANDS Logic Controls pole displays are controlled by command codes and data from the computer. Commands are transm

iCustomer Displays2 by 20 character displayUSER MANUAL Models: LD9000 Series

iiNOTICEThe manufacturer of the POS pole display makes norepresentations or warranties, either expressed or implied, byor with respect to anything in

iiiTABLE OF CONTENTSFEATURES ...1MODEL IDENTIFICATION...

1FEATURESThe LD9000 family of pole displays offers a wide range of high qualityfeatures and models to choice from. Listed below are the featuresincorp

2MODEL IDENTIFICATIONLD9 __ __ __ - __ __X = Double Sided DisplayPT = Pass Thru25 = DB25F connector to computerPOWER ADAPTER 0 = 120VAC*COMMAND

3INSTALLATIONYour PD9000 family of pole displays has been pre-assembled tomake the installation as simple as possible.Serial Interface Non-pass-thru M

4Serial Interface Pass-thru Models Installation1 Mount the pole display to the metal base plate using themounting hardware provided.2 The pole displ

5FUNCTIONAL TESTThe following test sequence will verify that your pole display isworking properly. Before you start this procedure, you must install

Product OverviewMain Unit orRear View2-8 Elo Entuitive Touchmonitor User Guide

6LD9100-PT, LD9300-PT, LD9400-PT and LD9500-PT1. Type “ABCDEFGH” and press ENTER key.The display will show“ABCDEFGH” on the first line.2. Type “^APASS

7LD9190-PT, LD9390-PT, LD9490-PT and LD9590-PT1. Type “ECHO ABCDEFGH>LPT1” and press ENTER key. Thedisplay will show “ABCDEFGH” on the first line.

8INTERFACE CONNECTIONSerial Interface Connector ConfigurationThe pin out configuration for the standard serial pole display is aDB9F connector. It plu

9Parallel Interface Connector ConfigurationAll standard parallel pole displays will have a DB25 male connector. Itis connected to the printer port of

10SOFTWARE COMMANDSLogic Controls pole displays are controlled by command codes anddata from the computer. The model of pole display that you have wi

117. Carriage Return <0D>, (13), {^M}:The cursor moves to the left most digit of the row it is in.8. Digit Select <10>, (16), {^P}:Moves t

1217. Both Side Display <1B><0C>, (27)(12), {^[ ]{^L}:After this command, all messages followed are displayed on bothsides of double sided

13PASS-THRU COMMAND SET (LD9100-PT, LD9100X-PT):All software commands of the non-pass-thru single sided model areavailable with following additional c

14HARDWARE CONFIGURATIONSerial pole displays were factory configured for serial RS232Cinterface using the following protocol:· 9600 Baud Rate· 8 Data

15DISPLAY CHARACTER CODESD7 0 0 0 0 0 0 0 0D6 0 0 0 0 1 1 1 1D5 0 0 1 1 0 0 1 1D4 0 1 0 1 0 1 0 1D3D2D1D00 1 2 3 4 5 6 70 0 0 0 0 DP SP 0 @ P ‘ p0 0 0

Side ViewBase Bottom View2-9or

16GENERAL SPECIFICATIONSLD9000 LD900XOPTICAL:Number of rows 2 2 x 2 sidesNumber of digits/row 20 20Dot matrix 5 x 7 5 x 7Digit height) 0.374in. (9.5mm

SecuGen _______________________________________________________ Products -1PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -2PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -3PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -4PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -5PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -6PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -7PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -8PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

SecuGen _______________________________________________________ Products -9PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD 0

KensingtonTM LockThe KensingtonTM lock is a security device that prevents theft. Tofind out more about this security device, do to http://www.kensingt

SecuGen _______________________________________________________ Products -10PC Peripheral Type, USB Fingerprint Recognition DeviceFDU02SGD

USB Interface ConnectionYour touchmonitor comes with only one touchscreen connector cables: USB cable. (ForWindows 2000, Me and XP systems only.)To se

CAUTION Before connecting the cables to your touchmonitor and PC, be sure that thecomputer and touchmonitor are turned off.NOTE Before connecting the

The following illustrations guide you step by step in connecting your touchmonitorusing a USB cable connection.Power cordConnect one end of the power

Elo Entuitive Touchmonitor User Guide15" LCD DesktopET1529L SeriesRevision BP/N 008603Elo TouchSystems, Inc.1-800-ELOTOUCHwww.elotouch.com

Video cableConnect one end of the video cable to the rear side of computer and the other to theLCD. Tighten by turning the two thumb screws clockwise

Speaker cableConnect one end of the speaker cable to the speaker port in the computer and the otherend to the port in the monitor.2-15

USB cableConnect one end of the USB cable to the rear side of the computer and the other to theLCD monitor.The USB cable is for optional touch, MS

Replace the Cable CoverCable cover lip cablesThen you have attached all the cables to the monitor, gently bring all the cables towardthe standard so t

Optimizing the LCD DisplayTo ensure the LCD display works well with your computer, configure the display modeof your graphic card to make it less than

Magnetic Stripe ReaderNo device are needed.Testing the USB MSR Keyboard Emulation1 Plug in the device.2 Open MS Word.3 Slide the card through the MSR

1.5 This dialog will appear1.6 Swipe Test card.1.7 Close Read Cards Dialog.1.8 Click on Send Command. The following dialog box will appear1.9 To send

1.11 Then click on Send Message.1.12 The DATA=00 means it’s USB HID.1.13 Switch to Keyboard Emulation1.14 Type 01 10 01 into area under the heading Me

1.19 The DATA=01 means it’s USB Keyboard Emulation.1.20 You must now reset the MSR by sending the command 02.1.21 Type 02 into area under the heading

1.2 click on About to verify version1.3 Close About Dialog.1.4 Click on Send Commands1.5 This Dialog will appear.1.6 To send Inquiry MSR type1.7 Type

Copyright © 2005 Elo TouchSystems Inc. All Rights Reserved.No part of this publication may be reproduced, transmitted, transcribed, stored in aretrie

1.9 The DATA=01 means it’s USB Keyboard Emulation.1.10 Switch to HID1.11 Type 01 10 00 into area under the heading Message(Hex)1.12 Then click on Send

1.19 Click on Read Cards…1.20 This dialog will appear1.21 Swipe Test card.1.22 Cose Read Cards Dialog.1.23 Done.2-25

Rear Facing Customer DisplayUSB Customer DisplayPlug in the USB cable attached to the Customer Display unit. The New Hardware Wiz-ard dialog box will

To test the drivers:1 In windows click on Start > Run2 Enter “cmd” > OK3 Type “ECHO ELO>\.\LCLD9\” > EnterThe display will show ELO.Instal

Installing the USB Touch DriverInstalling the USB Touch Driver for Windows XP, Windows 2000,Me and 981 Insert the Elo CD-ROM in your computer’s CD-ROM

C H A P T E R3OPERATIONAbout Touchmonitor AdjustmentsYour touchmonitor will unlikely require adjustment. Variations in video output and ap-plica

5432115.0” LCD Function KeyControls Function1 Power Switch Turns the display system power on or off.2 Select Displays the OSD menus on the screen and

Controls and AdjustmentOSD Lock/UnlockYou are able to lock and unlock the OSD feature. The monitor is shipped in the unlockedposition.To lock the OSD:

OSD Control OptionsBrightness• Background Luminance of the LCD panel is adjusted.Contrast• Adjusts the contrast or the values of color gain (RED, GREE

Language• Languages used for OSD menu display: English, French, German, Spanish and Japanese.Recall Defaults• Recalls the factory OSD default setting

Chapter 1Introduction 1Product Description ... 1Detailed LCD Display PerformanceRequirements ...

CAUTION In order to protect the LCD, be sure to hold the base when adjusting the LCD,and take care not to touch the screen.3-34 Elo Entuitive Touchm

432112.1” LCD Function KeyControls Function1 Select Displays the OSD menus on the screen and used toselect (“Clockwise” and “Counter-clockwise” direct

Controls and AdjustmentOSD Lock/UnlockYou are able to lock and unlock the OSD feature. The monitor is shipped in the unlockedposition.To lock the OSD:

OSD Control OptionsBrightness• Background Luminance of the LCD panel is adjustedContrast• Gain of R, G, and B signal is adjusted.Phase• The phase of t

Language• Select the language used for the OSD menu from among English, French,Deutsch, Spanish, and Japanese.Recall Defaults• Restore all original fa

C H A P T E R4TROUBLESHOOTINGIf you are experiencing trouble with your touchmonitor, refer to the following table. Ifthe problem persists, pleas

4-40 Elo Entuitive Touchmonitor User Guide

C H A P T E RANATIVE RESOLUTIONThe native resolution of a monitor is the resolution level at which the LCD panel isdesigned to perform best. For

As an example, a SVGA resolution LCD panel has 800 pixels horizontally by 600 pixelsvertically. Input video is also represented by the same terms. XGA

C H A P T E RBTOUCHMONITOR SAFETYThis manual contains information that is important for the proper setup and maintenanceof your touchmonitor. Be

Touchmonitor Specifications ... 46AccuTouch TouchscreenSpecifications ... 47Intell

Care and Handling of Your TouchmonitorThe following tips will help keep your Elo Entuitive touchmonitor functioning at theoptimal level.• To avoid ris

C H A P T E RCTECHNICAL SPECIFICATIONSDisplay ModesYour Elo Entuitive touchmonitor is compatible with the following standardvideo modes:Item Res

Touchmonitor SpecificationsModel ET1529LLCD Display 15.0” TFT Active Matrix PanelDisplay Size 304.1(H) x 228(V) mmPixel Pitch 0.297(H) x 0.297(V) mmDi

AccuTouch Touchscreen SpecificationsMechanicalConstruction Top: Polyester with outside hard-surface coating with clear orantiglare finish.Inside: Tran

IntelliTouch Touchscreen SpecificationsMechanicalPositional Accuracy Standard deviation of error is less than 0.080 in. (2.03 mm).Equates to less than

Infrared Touchscreen SpecificationsMechanicalInput Method Input Method Finger or gloved hand activationElectricalPositional Accuracy Typical centroid

15” LCD Touchmonitor(ET1529L-XXXA-1-XX-T) Dimensions15” LCD Touchmonitor(ET1529L-XXXA-1-XX) DimensionsC-50 Elo Entuitive Touchmonitor User Guide15

REGULATORY INFORMATIONI. Electrical Safety Information:A) Compliance is required with respect to the voltage, frequency, and current require-ments ind

This Information Technology Equipment (ITE) is required to have a CE Mark onthe manufacturer’s label which means that the equipment has been tested to

53"The application of this monitor is restricted to special controlled luminous environments.The screen surface trend toreflect annoying light

54 Elo Entuitive Touchmonitor User Guide

WARRANTYExcept as otherwise stated herein or in an order acknowledgment delivered to Buyer,Seller warrants to Buyer that the Product shall be free of

THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES FORBREACH OF WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SETFORTH ABOVE, SELLER GRANTS

Numerics15.0" LCD Touchmonitor (ET1529L-XXWA-1)Dimensions, 50AAbout Touchmonitor Adjustments, 29AccuTouch Touchscreen Specifications, 47Auto Adju

NNative Resolution, 41OOptical, AccuTouch, 47Optical, IntelliTouch, 48Optical, IR, 49Optimizing the LCD Display, 18OSD Control Options, 32,36OSD Left/

USB INTELLIHEAD FOR SWIPE READERS TECHNICAL REFERENCE MANUAL Manual Part Number 99875320-1P OCTOBER 2004 PRELIMINARY REGISTERED TO ISO 9001:2000

ii Copyright©2004 MagTek®, Inc. Printed in the United States of America Information in this document is subject to change without notice. No part of

iii Limited Warranty MagTek, Inc. warrants that the Product described in this document is free of defects in materials and workmanship for a period o

iv FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of FCC R

C H A P T E R1INTRODUCTIONProduct DescriptionThe ET1529L is a retail terminal designed to present information to the operator and thecustomer. T

vTABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS ... 1 FEATURE

vi Figure 1-1. 3-Track USB IntelliHead

1SECTION 1. FEATURES AND SPECIFICATIONS The USB (Universal Serial Bus) IntelliHead Swipe Reader is a compact magnetic stripe card reader that confor

USB IntelliHead Swipe Reader 2CONFIGURATIONS The Configurations are as follows: Table 1-1. Configurations ACCESSORIES The accessories are as follow

Section 1. Features and Specifications3SPECIFICATIONS Table 1-2 lists the specifications for the USB IntelliHead. Figure 1-2 shows the dimensions f

USB IntelliHead Swipe Reader 4

5SECTION 2. INSTALLATION This section describes the cable connection, the Windows Plug and Play Setup, and the physical mounting of the unit. USB C

USB IntelliHead Swipe Reader 6

7SECTION 3. OPERATION CARD READ A card may be swiped past the read head at any time. The magnetic stripe must face toward the head and may be swip

USB IntelliHead Swipe Reader 8

The credit card reader reads all three stripes on a standard credit card or drivers license.The credit card is read by sliding the credit card, stripe

9SECTION 4. USB COMMUNICATIONS This device conforms to the USB specification revision 1.1. This device also conforms with the Human Interface Device

USB IntelliHead Swipe Reader 10 following table. The usage types are also listed. These usage types are defined in the HID Usage Tables document. M

Section 4. USB Communications11 Item Value (Hex) Input (Data, Variable, Absolute, Buffered Bytes) 82 02 01 Usage (Command message) 09 20 Report Cou

USB IntelliHead Swipe Reader 12 TRACK 1 DECODE STATUS Bits 7-1 0 Value Reserved Error This is a one-byte value, which indicates the status of decod

Section 4. USB Communications13 CARD ENCODE TYPE This one-byte value indicates the type of encoding that was found on the card. The following table

USB IntelliHead Swipe Reader 14 COMMANDS Most host applications do not need to send commands to the device. Most host applications only need to obt

Section 4. USB Communications15 RESULT CODE This one-byte field contains the value of the result code. There are two types of result codes: generi

USB IntelliHead Swipe Reader 16 Property ID is a one-byte field that contains a value that identifies the property. The following table lists all the

Section 4. USB Communications17 SERIAL_NUM PROPERTY Property ID: 1 Property Type: String Length: 0 – 15 bytes Get Property: Yes Set Property: Y

USB IntelliHead Swipe Reader 18 rate decreases the USB bus bandwidth used by the device. This property is stored in non-volatile EEPROM memory so it

12.1 Customer Display TFT LCD Display PanelDisplay Format 800x600Display area 12.1” 246.0mm(H) x 184.5mm(V)Pixel Pitch 12.1” 0.3075mm(H) x 0.3075mm(V

Section 4. USB Communications19 01 02 03 08 Example Set MAX_PACKET_SIZE property Response (Hex): Result Code Data Len Data 00 00 Example Get MAX_

USB IntelliHead Swipe Reader 20 Result Code Data Len Prp Value 00 01 00

21 SECTION 5. DEMO PROGRAM The demo program, which is written in Visual Basic, can be used to do the following: • Read cards from the device and vie

USB IntelliHead Swipe Reader 22 SOURCE CODE Source code is included with the demo program. It can be used as a guide for application development. I

23 APPENDIX A. USB INTELLIHEAD SWIPE READER The following drawing is provided in this section: Part Number Title 21030006 USB-HID INTHD 3TK 125MM

USB IntelliHead Swipe Reader24Figure A-1. USB HID IntelliHead, 3-Track, 125mm Wire, 5-Pin Connector

Preliminary to Rev 1 10/20/2004 7:30:02 AM USB INTELLIHEAD KEYBOARD EMULATION FOR SWIPE READERS TECHNICAL REFERENCE MANUAL Manual Part Number 9987

iiCopyright©2004 MagTek®, Inc. Printed in the United States of America Information in this document is subject to change without notice. No part of

iiiLimited Warranty MagTek, Inc. warrants that the Product described in this document is free of defects in materials and workmanship for a period of

ivFCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of FCC Rul